FFC/FPC连接器 1.0mm间距 4P~32P
ffc/fpc扁平电缆连接器间距有0.3、0.5、0.8、1.0、1.25、2.54mm,4~68屏数多规格系列广泛应用于音响、数码机、摄像机、汽车音响、电视机、打字机、计算器、收款机、电话、cd-rom、vcd、dvd、复印机、打印机、无线仪器仪表、视叫设备及航空航天产品高新科技先锋 产品规格书
product specification【1】适用范围 scope
本规格书适用于:1.0间距柔性扁平电缆连接器
this specification covers the 1.0mm pitch fpc/ffc connectors(series locking)
【2】产品名称及型号 product name and part number
产品名称 product name | 产品型号part number |
ffc/fpc扁平电缆连接器 | |
|
【3】定格 ratings
项目 item | 规 格 requirement | ||
Zui大容许电压 rated voltage(max) | 50v | [ac/dc(有效值 virtual value)50hz] | |
Zui大容许电流 rated current(max) | 0.4a | ||
使用温度范围 ambient temperature range | -25℃ ~ +85℃ | ||
【4】性能 performance
4.1电气性能 electrical performance
项目 item | 条 件 test condition | 规格 requirement | |
4.1.1 | 接触电阻 contact resistance | 适合fpc/ffc嵌合;开放电压20mv以下;短路电流10ma的状态下测定。 mate applicable fpc/ffc and measure by dry circuit,20mv max,10ma. | ≤20 mωmax |
4.1.2 | 绝缘电阻 insulation resistance | 适合fpc/ffc嵌合;相邻端子间或端子与地面间加dc 500v下测定。 mate applicable fpc/ffc and apply 500v dc between adjacent terminal or ground. | 500mωmin |
4.1.3 | 耐电压 dielectric | 适合fpc/ffc嵌合;相邻端子间或端子与地面间加ac 200v(有效值)历时1分钟下测定。 mate applicable fpc/ffc and apply 200v ac(virtual value)for 1minute between adjacent terminal or ground. | 无击穿现象 no breakdown |
4.2机械性能 mechanical performance
项目 item | 条 件 test condition | 规格 requirement | |
4.2.1 | 锁紧力及拔出力 locking and withdrawal force | 适合0.3mm厚的ffc;用每分钟25±3mm的速度;平行地插入、锁紧、拔出。 insert and extract applicable ffc at the speed rate of 25±3mm/minute. | 锁紧力 locking 1.96*n (n) max 拔出力 withdrawal 0.49*n (n) min |
4.2.2 | 端子保持力 terminal /housing retention force | 以用每分钟25±3mm的速度平行向外拉 pull the terminal at the speed rate of 25±3mm per minute | 3.92n min |
4.3环境和其他性能 environmental performance and others
项目 item | 条 件 test condition | 规格 requirement | ||
4.3.1 | 重复插拔 repeated insertion and withdrawal | 无通电状态;以10次/分钟的速度插拔20次 insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute | 接触抵抗 contact resistance | 60 mωmax |
4.3.2 | 温度上升 temperature rise | 适合fpc/ffc嵌合;Zui大容许电流通电,温度测定。(ul 498) carrying rated current load.(ul 498) | 温度上升 temperature rise | 30 ℃max |
项目 item | 条 件 test condition | 规格 requirement | ||
4.3.3 | 耐振动性 vibration | dc 1ma通电状态下;嵌合轴沿xyz三个方向振动;振幅1.5mm;频率10-55-10hz/分;历时2小时 amplitude:1.5mm p-p sweep time:10-55-10hz in 1 minute duration:2 hours in each x.y.z. axes | 外观 appearance | 无损坏 no damage |
接触抵抗 contact resistance | 60 mωmax | |||
瞬断 discontinuity | 1 ms max. | |||
4.3.4 | 耐冲击性 shock | dc 1ma通电状态下;嵌合轴沿相互垂直的6个方向;以490m/s2{50g}冲击;各3次 490m/s2{50g},3 strokes in each x.y.z. axes. | 外观 appearance | 无损坏 no damage |
瞬断 discontinuity | 1 ms max. | |||
4.3.5 | 耐热性 heat resistance | 适合fpc/ffc嵌合;85±2℃的空气中;放置96小时;再回到室温中放置1-2小时 85±2℃,96 hour | 外观 appearance | 无损坏 no damage |
接触抵抗 contact resistance | 60 mωmax | |||
4.3.6 | 耐寒性 cold resistance | 适合fpc/ffc嵌合;-40±2℃的空气中;放置96小时;再回到室温中放置1-2小时 -40±2℃,96 hour | 外观 appearance | 无损坏 no damage |
接触抵抗 contact resistance | 60 mωmax | |||
4.3.7 | 耐湿性 humidity | 适合fpc/ffc嵌合;40±2℃、相对湿度90-95%的空气中;放置96小时;再回到室温中0.5小时内测定 temperature:40±2℃ relative humidity:90-95% duration:96 hours | 外观 appearance | 无损坏 no damage |
接触抵抗 contact resistance | 60 mωmax | |||
耐电压 dielectric strength | 必须满足4.1.3 must meet 4.1.3 | |||
绝缘抵抗 insulation resistance | 20 mω min | |||
4.3.8 | 温度循环 temperature cycling | 适合fpc/ffc嵌合;-55±3℃ 30分钟;常温常湿 10-15分钟;85±2℃ 30分钟;常温常湿 10-15分钟,循环5次。 5 cycles of: a) -55±3℃ 30 minutes b) 85±2℃ 30 minutes | 外观 appearance | 无损坏 no damage |
接触抵抗 contact resistance | 60 mωmax |
项目 item | 条 件 test condition | 规格 requirement | ||
4.3.9 | 耐盐雾性 salt spray | 适合fpc/ffc嵌合;35±2℃、5±1%的盐水喷雾48小时;试验后常温水洗;再室温干燥。 48±4 hours exposure to a salt spray from the 5±1% solution at 35±2℃. | 外观 appearance | 无损坏、腐蚀 no damage |
接触抵抗 contact resistance | 60 mωmax | |||
4.3.10 | 耐亚硫酸 so2 gas | 适合fpc/ffc嵌合;40±2℃、50±5ppm的亚硫酸中放置24小时 24 hours exposure to 50±5ppm. so2 gas at 40±2℃. | 接触抵抗 contact resistance | 60 mωmax |
4.3.11 | 耐氨性 nh3 gas | 适合fpc/ffc嵌合;浓度为28%的氨水容器中;放置40分钟。 40 minutes exposure to nh3 gas evaporating from 28% ammonia solution | 外观 appearance | 无损坏 no damage |
接触抵抗 contact resistance | 60 mωmax | |||
4.3.12 | 可焊性 solder ability | 端子前端基准面0.2mm处浸入235±5℃的锡槽中;历时2±0.5 sec。 soldering time:2±0.5 sec. soldering temperature:235±5℃ 0.2 mm from terminal tip | 沾敷性 solder wetting | 沾敷面积95%以上
|
4.3.13 | 耐焊接热 resistance to soldering heat | 端子前端基准面0.2mm处浸入260±5℃的锡槽中;历时5±0.5 sec。 soldering time:5±0.5 sec. soldering temperature:260±5℃ 0.2 mm from terminal tip | 外观 appearance | 无损坏、变形 no damage |
( ) :参考规格 reference standard
{ } :参考单位 reference unit
【5】外观形状、寸法及材质product shape,dimensions and materials
图面参照 refer to the drawing.
名 称 name | 材 质 materials |
主体 main body | lcp(本色) ul 94v-0 |
锁扣 housing lock | lcp(黑色) ul 94v-0 |
端子 sit uip | 磷青铜 phosphor bronze |
焊片 contact | 磷青铜 phosphor bronze |
备注 remark | 金属表面镀锡 |
本产品的品牌是银胜,型号是FPC连接器1.0mm间距下接,种类是FFC/FPC,工作频率是低频,应用范围是显示屏,接口类型是ZIF,支持卡数是单卡,读卡类型是CF,形状是条形,制作工艺是熔接,加工定制是是,特性是防潮,接触件材质是磷青铜,绝缘体材质是LCP,芯数是4-32,针数是4-32